Sennheiser TV Mount LAH 500 User Manual

LAH 500  
Loudspeaker  
Mounting Hardware  
Mounting instructions  
 
Important safety and mounting instructions  
important safety and mounting instructions  
X
Have the product mounted by specialists.  
Due to their technical training, know-how and experience as well as knowledge of relevant  
provisions, regulations and standards, specialists must be able to assess assigned tasks,  
recognize potential hazards and ensure appropriate safety measures. The following safety  
and mounting instructions are addressed to specialists.  
X
Read and follow the safety and mounting instructions, keep these instructions and always  
include them when passing the LAH 500 on to third parties.  
X
X
Only use the LAH 500 for mounting the LSP 500 PRO.  
Also read and follow the safety and installation instructions contained in the operating  
manual of the LSP 500 PRO.  
X
Always use the LAH 500 in combination with the following accessories:  
- Neumann LH 29 TV spigot or  
- König & Meyer TV pin 24519  
X
X
Do not install the LAH 500 in locations where it is exposed to externally generated  
vibrations.  
Observe and follow the local, national and international regulations and standards:  
- when selecting a suitable truss and when assessing the proper attachment of the truss,  
- when selecting a suitable and sufficiently dimensioned holder for TV spigot,  
- when mounting the LAH 500 with the attached LSP 500 PRO.  
cAUtioN!  
Danger of injury and material damage due to dropping of the LAh 500, the tv spigot/tv pin  
and the LSP 500 Pro  
Unless the LAH 500, the TV spigot/TV pin and the LSP 500 PRO are properly attached to a truss,  
these parts can drop down.  
X
X
Before attaching to a truss, make sure that the LAH 500, the TV spigot/TV pin used and the  
LSP 500 PRO are fastened to each other as described in the following text and shown in the  
figures at the beginning of the document. Tighten all screws with the torques specified in  
the figures.  
Use a safety wire to secure the LAH 500 and the LSP 500 PRO to the truss during mounting.  
The safety wire must be rated for the attached load. The safety wire, rope terminations and  
coupling links must comply in their dimensioning and condition with the regulations and  
standards of the country in which they are used and must reliably prevent tipping/dropping  
of the attached parts.  
X
When mounting, have the LSP 500 PRO held by a second specialist who is physically able to  
do so. The requirements mentioned earlier also apply to this specialist!  
X
X
Make sure that the truss is undamaged, properly attached and rated for the weight to be  
carried.  
Fasten and secure a suitable holder for TV spigot to the truss. The holder must be able  
to carry the weight of the LSP 500 PRO plus the weight of the TV spigot/TV pin and the  
LAH 500. Calculate the total weight and, if necessary, consider additional leverages.  
X
X
X
X
X
Dismount the LAH 500 as shown in fig. 1.  
Attach the TV spigot/TV pin to the upper mounting plate of the LAH 500 as shown in fig. 1.  
Attach the LAH 500 to the LSP 500 PRO as shown in figs. 2 to 2.2.  
Fasten the LAH 500 to the truss by inserting the TV spigot/TV pin to the holder for TV spigot.  
Secure the combination of TV spigot and holder as shown in fig. 2.3. The TV spigot/TV pin  
has to be secured to the holder with the metal locking pin.  
1 | LAH 500  
 
Important safety and mounting instructions  
X
X
Rotate the LSP 500 PRO horizontally as desired and then secure this position using the  
safety screw of the holder (see fig. 2.3).  
Use a safety wire to secure the LAH 500 and the LSP 500 PRO to the truss as shown in  
fig. 2.3. The safety wire must be rated for the attached load. The safety wire, rope termina-  
tions and coupling links must comply in their dimensioning and condition with the regula-  
tions and standards of the country in which they are used and must reliably prevent tip-  
ping/dropping of the attached parts.  
X
Make sure that ...  
- the LSP 500 PRO cannot tip over or drop down, even if the power or audio cables are  
pulled;  
- you replace the safety wires and coupling links by new ones when they have prevented  
tipping/dropping;  
- you check every 3 months if all screws are tightened with the torques specified in these  
safety and mounting instructions and if the LSP 500, the LAH 500, the TV spigot/TV pin,  
additional fastening elements, safety wires as well as the coupling links are in proper  
condition.  
In case of any damage or any deviation from the safety and mounting instructions, immedi-  
ately dismount the LSP 500 PRO, the LAH 500 and the additional mounting hardware used.  
Package contents  
1 upper mounting plate  
1 lower mounting plate with spacer (premounted)  
2 knurled screws for joining the upper and the lower mounting plate  
The Neumann LH 29 TV spigot, the König & Meyer TV pin 24519 and the safety wires have  
to be ordered separately.  
Specifications  
Weight:  
2.4 kg  
Dimensions:  
65 x 190 x 188 mm (H x W x D)  
Warranty  
Sennheiser electronic GmbH & Co. KG gives a warranty of 24 months on this product.  
tact your Sennheiser partner.  
LAH 500 | 2  
 
Sennheiser electronic GmbH & Co. KG  
Am Labor 1, 30900 Wedemark, Germany  
Publ. 08/13, 554629/A01  
 

Silvercrest Hair Care Product SHGR 75 A1 User Manual
Sony Car Stereo System NSZ GS7 NSZ GX70 User Manual
Sony Computer Drive SDX 800V User Manual
Sony Ericsson Stereo System CDX M620 User Manual
Sony Home Theater System DAVHDZ273 User Manual
Speco Technologies Security Camera CVC 1705 User Manual
Speco Technologies Security Camera VLB11SCSFF User Manual
Star Manufacturing Convection Oven CCOH 3 User Manual
Star Manufacturing Food Warmer 174CBA User Manual
Stovax Indoor Fireplace VFC Radiant Convector Fire Range User Manual