Sanyo Projector PLC User Guide

Sanyo Installation  
Configuration and Connections  
SYSTEM 4xi  
PROJECTOR COMMUNICATIONS KIT  
ATTENTION!  
PLEASE READ THIS DOCUMENT FOR IMPORTANT  
INSTALLATION INSTRUCTIONS  
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:  
Kit Type: SANYO  
Included Communications Adapter(s):  
Quantity  
Part Number  
26-467-01  
26-489-01  
Description  
ADP, UNV, A”  
ADP, UNV, J”  
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING  
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS  
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS  
INDICATED BY THE “” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL  
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER  
WITH THE CORRECT SETTINGS.  
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND  
SIGNAL CONNECTION INSTRUCTIONS.  
THIS SWITCHER HAS BEEN CONFIGURED FOR: SANYO PLC  
CONFIG  
AS  
MODEL  
SW1  
SW2 SW3 SW4 SW5 SW6 PROJ  
COMM  
1
2
3
4
CABLE ADAPTER  
PLC  
off on off on  
off on off on  
off on off on  
0
0
0
0
0
0
1
1
1
E
E
E
0
0
0
J15  
J15  
J15  
26-467-01  
26-489-01  
26-489-01  
PLC 8810  
PLC XP10  
PLC XP30  
off on off on  
0
1
1
E
0
J15  
26-489-01  
Page1  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-402-02 Rev. E  
 
Sanyo Installation  
Configuration and Connections  
5. The Sanyo PLC Comm Adapter (26-467-01) has a 9-pin male connector that  
accommodates the Comm Extension cable. The other end of the Comm Adapter  
plugs into the projector’s RS-232C port.  
6. Plug the 15-pin HD connector of the Projector Communications Extension cable  
into the PJ Comm port on the System 4xi.  
______ Secure all of the connector screws.  
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV  
cable onto the System 4xi output and those on the other end onto the matching  
BNCs on the Sanyo PLC connector panel.  
System 4xi Series – Sanyo PLC Projector Connections  
Use the illustration below as a guide when connecting the System 4xi to a Sanyo  
PLC Projector. Refer to Sanyo documentation to continue the installation.  
See Special Note below  
R
G
B
H
V
USB 1 CONTROL PORT 1  
VIDEO/Y C/Cb(B-Y) Cr(R-Y)  
VIDEO/Y C/Cb(B-Y) Cr(R-Y)  
VIDEO/Y C/Cb(B-Y) Cr(R-Y)  
S-VIDEO  
S-VIDEO  
S-VIDEO  
AUDIO 1  
AUDIO 1  
R
L
R
L
ANALOG RGB  
ANALOG RGB  
AUDIO 1  
USB 2 CONTROL PORT 2  
AUDIO 2  
R
L
R
L
AC JACK SERIAL PORT  
AUDIO 1  
AUDIO OUT  
R
L
R
L
9-Pin Male  
ComAdapter  
26-467-01 "A"  
or 26-489-01 "J"  
A
9-Pin Male  
9-Pin Female  
RGBHV 5 BNC  
15-Pin  
Male  
INPUT 1  
H/HV  
INPUT 2  
INPUT 3  
INPUT 4  
H/HV  
OUTPUT  
H/HV  
PJ COMM  
V
H/HV  
V
H/HV  
V
V
V
AUDIO  
AUDIO  
B
AUDIO  
AUDIO  
B
AUDIO  
RS 232  
R/C  
G/Y  
B
R/C  
G/Y  
R/C  
G/Y  
B
R/C  
G/Y  
R/C  
G/Y  
B
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the  
System 4xi. See page 2-5 for cabling guidelines.  
Special Note: _____ Certain PLC projectors may not come equipped with a 9-pin serial port  
connector. In those situations, the Com adapter must be connected to Control  
Port 2 using the projector’s special DIN to 9-pin serial adapter, as illustrated  
below.  
t
To switcher's Projector Control por  
ort 2  
To projector's Control P  
Sanyo DIN to 9-pin adapter  
Extron Com Adapter  
26-467-01 "A"  
or 26-489-01 "J"  
Page3  
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-402-02 Rev. E  
 

Python Automobile Alarm 400 ESP User Guide
Quatech Network Card SPPXP 100 User Guide
RCA Network Router 716v5 WL User Guide
ResMed Network Card 608140 20611 User Guide
RIDGID Planer JP0610 User Guide
RoyalTek GPS Receiver MEB 1000 User Guide
Samsung Printer MSYS 5200 User Guide
Samsung Stereo System C6600 User Guide
Samsung Washer P1003J User Guide
Schlage Door AL SERIES User Guide