Samsung Boat SH S202GTS H652G User Guide

SH-S202G(TS-H652G)ENG/RUS 2007.4.15 11:28 PM Page 1  
Warning/Caution  
Introduction  
Safety Precautions  
The following are basic precautions to ensure user safety  
to the  
Connecting the Cables  
DVD Writer  
Warning: To warn the user that failure to comply with the instructions may result in  
Super- DVD Writer  
SH-S202G(TS-H652G)  
serious injury or death.  
Caution:  
To caution the user that failure to comply with the instructions may result in  
damage to property.  
and reduce the risk of property damage.  
Design and specifications are subject to change without prior notice.  
Connecting the Cables  
Eject Button  
User Guide - ENGLISH  
Disc compartment  
When you install the drive  
Place the drive on a level  
surface.  
FCC Compliance  
Do not drop the drive, and  
protect it fromsevere shocks.  
Never allow food particles or  
foreign substances to enter the  
drive casing.  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
Avoid high-humidity environments.  
Failure to do so may cause the  
device to fall onto a hard surface,  
resulting in damage or malfunction.  
Power cable  
It can damage the drive or cause  
it to malfunction.  
pursuant to Part 15 of the FCC rules.  
Front  
These limits are designed to provide reasonable protection against harmful interference in a  
residential installation.  
EIDE cable  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception,  
which can be deter-mined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
Master/slave select terminal  
Audio cable  
Disc compartment  
LED  
• Re-orient or relocate the receiving antenna.  
Emergency eject hole  
• Increase the separation between the equipment and receiver.  
While operating  
If the compartment does not open  
when you press the Eject button,  
power off the computer, insert a pin  
or unfolded paper clip in the hole  
and push firmlhy)  
• Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
Do not move the drive while in operation and  
do not attempt to open the disc tray byforce.  
Make sure to close all working programs before  
attempting to open the tray and always use the  
open/close button.  
If the power cable is not connected  
properly, it may cause a fire or  
damage the drive. Check the direction  
of the power connector and the drive  
incline before connection.  
• Consult the dealer or an experienced radio/TV technician for help.  
To protect against the risk of  
fire, do ot spill such liquids as  
alcohol and benzene on the  
drive.  
Avoid low- or high-temperature  
environments.  
Connecting the power cable  
CAUTION  
1
2
Change or modifications not expressly approved by the manufacturer responsible for  
The 4-pin power cable from the internal power unit of your computer must  
be connected to the power terminal the rear of the DVD Writer.  
compliance could void the user ’s authority to operate the equipment.  
LASER STANDARD  
IEC 60825-1 :1993 +A1 :1997 +A2 :2001  
Interface terminal  
Sound output terminal  
Connecting the EIDE cable  
• Insert the EIDE cable, which is connected to the hard  
disk to the interface terminal.  
WEEE  
+5V DC  
Ground  
Ground  
Correct Disposal of This Product (Waste Electrical &Electronic Equipment)  
(Applicable in the European Union and other European countries with separate collection systems)  
+12V DC  
Do not insert a pin into the emergency  
opening while in operation.  
(Place the red line of the cable close to the Pin 1.)  
This marking shown on the product or its literature,indicates that it should not be disposed with  
other household wastes at the end of its working life.To prevent possible harm to the  
Rear  
Installing a jumper on the master/slave select terminal  
• Connect a jumper to the rear side of the DVD Writer.  
Other  
3
environment or human health from uncontrolled waste disposal,please separate this from other  
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.  
Do not use cracked, distorted or  
damaged discs.  
Handle with caution to prevent  
damage from external shock.  
Do not disassemble, attempt to repair  
or modify the device without express  
approval as directed in the manual.  
If the jumper is connected to MA (Master), it will work in the Master mode.  
If the jumper is connected to SL (Slave), it will work in the Slave mode.  
If the jumper is connected to CS (CSEL), you can control the device by using the  
host interface signal CSEL. (In general, connection to MA is recommended.)  
Household users should contact either the retailer where they purchased this product,or their  
local government office,for details of where and how they can take this item for environmentally  
safe recycling.  
Do not place the drive in  
direct sunlight.  
To reduce the risk of damage,  
electric shock, and fire.  
Business users should contact their supplier and check the terms and conditions of the purchase  
contract.This product should not be mixed with other commercial wastes for disposal.  
Digital output Master/slave select terminal  
terminal  
Power terminal  
CS : Cable Select(CSEL)  
SL : Slave  
MA: Master  
Samsung Eco-mark  
The Samsung’s own Eco mark helps consumers to easily understand that  
Samsung develops eco-friendly products. This mark represents Samsung’s  
continuous effort to develop eco-friendly products.  
Accessories  
In particular, a disc with a crack on the  
inner tracks may break while in use.  
• RoHS  
User Guide, Screw 4ea  
(Restriction of the use of certain hazardous substances in electrical and electronic equipment)  
The RoHS, the environment regulation announced by European Union, restricts the use of  
lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the  
market in The European Union after July 1, 2006.  
Any change or modification not expressly approved by designated qualified personnel could  
void your authority to operate this device.  
1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that  
you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it  
will eventually result in irreparable damage to the disc.  
Design and specifications are subject to change without prior notice.  
* To write with the highest speed(20X), you must use 80 pin E-IDE cable.  
Connecting the EIDE cable from a sound card  
• Connect the 4-pin audio cable between the sound output terminal on the  
DVD Writer and the audio input terminal on the sound card.  
4
Important to read and understand  
Do not disassemble  
at all times  
2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).  
BG68-01416A REV.00  
1
2
3
4
Using the Drive/Storing and Cleaning  
Solving Technical Problems  
Installing the Drive  
Technical Specifications  
Your Discs  
The friction noise generated during SPIN-UP and STOP is caused by the  
Automatic Ball Balancing System(ABS) and is not a malfunction.  
When using one EIDE cable  
System Requirements  
Using the DVD Writer  
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear  
of the DVD Writer.  
Intel Pentium 800MHz(or higher), 256 MB of RAM (or higher)with an EIDE  
interface,Windows 2000/ XP/ Vista  
SH-S202G(TS-H652G)  
Check that the power, audio and EIDE cables are correctly  
connected to the computer.  
Push the power button and boot the computer.  
The DVD Writer is not  
detected by the computer.  
Category  
1
DVD Writer  
Slave Drive (Choose the SL Jumper)  
Change the EIDE cable and reconnect it to the computer.  
Preferably, connect a second EIDE cable to the DVD Writer  
in master mode.  
DVD : DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-ROM, DVD-Video,  
DVD+R (Dual), DVD-R (Dual), DVD-RAM, DVD Multi-Border  
After booting the computer, open the disc  
2
After installing the DVD Writer  
,
Installing the DVD Writer  
CD : CD-ROM, CD-R, CD-RW, CD-DA, CD+E(G)  
compartment by pressing the Eject button.  
Usable Discs  
CD-MIDI, CD-TEXT, CD-ROM XA, Mixed Mode CD CD-I,  
the PC gets slower.  
DISC  
Check the position of the jumper in the master/slave select  
terminal.  
CD-I Bridge (Photo-CD, Video-CD),  
How to install the DVD Writer on your PC. First, remove the cover;  
connect the cable to the DVD Writer and then to the PC.  
Insert the disc (CD) with the label on the disc  
Multisession CD (Photo-CD, CD-EXTRA, Portforio),  
3
facing upwards and close the disc compartment  
The DVD Writer is not  
Reinstall the device driver or update it with the latest version  
by downloading it from the Samsung Web site.  
Disc Diameter  
Interface Port  
PIO mode  
DMA mode  
CD-ROM  
4.72 Inch or 3.15 Inch (120mm or 80mm)  
ATA/ATAPI (E-IDE)  
MainBoard  
Hard Drive  
If necessary, attach a horizontal bracket  
by pressing the Eject button. The indicator light  
comes on.  
Play the disc (CD).  
recognized by MS-DOS.  
1
Interface  
Support  
to both sides of the drive.  
PIO Mode 4: 16.6MB/sec  
Ultra DMA Mode 4: 66MB/sec  
110ms (Random)  
When using two EIDE cable  
You can purchase these accessories separately  
from your computer dealer.  
4
The DVD Writer is not  
detected by Windows.  
This case may occur when there is a Windows installation  
problem; reinstall Windows.  
Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear  
of the DVD Writer.  
Access time  
(Random)  
(Screws for use: M3 X 6 X 4)  
Playing CD-DA/Audio CDs  
DVD-ROM  
130ms (Random)  
- If there is only one Optical drive: select MA (Master).  
Check whether the CD is of good quality and clean it,  
if necessary.  
A CD is not read or is read  
too slowly.  
Run the CD player program supplied with the sound card or play the  
Windows Media Player.  
Media Type  
DVD+R  
Write  
Read  
CAV 20X (27.0MB/sec)  
ZCLV 8X (10.8MB/sec)  
ZCLV 12X(16.2MB/sec)  
ZCLV 12X(16.2MB/sec)  
CAV 20X (27.0MB/sec)  
CLV 6X (8.1MB/sec)  
PCAV 12X (16.2MB/sec)  
-
CAV 16X (21.6MB/sec)  
CAV 12X (16.2MB/sec)  
CAV 12X (16.2MB/sec)  
CAV 12X (16.2MB/sec)  
CAV 16X (21.6MB/sec)  
CAV 12X (16.2MB/sec)  
PCAV 12X (16.2MB/sec)  
CAV 16X (21.6MB/sec)  
CAV 12X (16.2MB/sec)  
CAV 48X (7.2MB/sec)  
CAV 40X (6.0MB/sec)  
CAV 40X (6.0MB/sec)  
CAV 40X (6.0MB/sec)  
CAV 40X (6.0MB/sec)  
Master Drive (Choose the MA Jumper)  
DVD+RW  
Playing Video CDs  
The disc compartment will  
not open.  
Check that the power cable is correctly connected.  
DVD+R DUAL  
DVD-R DUAL  
DVD-R  
Follow the instructions provided with the disc.  
A video card or MPEG software and a sound card need to be installed to view video CDs.  
Power off and disconnect the PC.  
Insert a pin or unfolded paper clip in the emergency hole and push  
firmly until the disc compartment opens.  
SEC 1  
PRI 1  
Remove the plate from a free expansion slot and install the  
DVD Writer, as shown in the illustration.  
DVD-RW  
If the drive is vertically installed, you cannot use an 8 cm Mini Disc  
because the disc is movable.  
2
Data transfer  
rate(MAX)  
DVD-RAM  
DVD-ROM(Single)  
DVD-ROM(Dual)  
CD-ROM  
When the MPEG software  
plays a Video CD, the pictures  
are not regular and the running  
speed is too slow.  
Adjust the size of the replay screen.  
If you have no free expansion slot, install the drive in place of the  
diskette drive.  
MainBoard  
After checking the display resolution, adjust it, if necessary.  
Hard Drive  
-
Storing Your Discs  
-
-If there is two Optical drive, select MA (Master) / SL (Slave).  
Make sure to use the standardized screws supplied (M3X6).  
Do not place a disc in direct sunlight.  
Store a disc vertically in a well-ventilated and  
stable location.  
Do not write or attach a label on a disc.  
Do not drop a disc or place heavy objects on it.  
CD-R  
PCAV 48X (7.2MB/sec)  
ZCLV32X (4.8MB/sec)  
CLV 10X (1.5MB/sec)  
CLV 4X (0.6MB/sec)  
Master Drive (Choose the MA Jumper)  
Slave Drive (Choose the SL Jumper)  
- To use screws other than M3X6 may result in malfunction.  
US-RW  
The Disc is not in message is  
displayed even though a disc  
has been inserted.  
HS-RW  
The computer may not recognize the disc if you start playback  
too quickly after inserting the disc.  
CD-RW  
SEC 1  
PRI 1  
Open and close the disc compartment and try again.  
Clean the disc and try again.  
Buffer Memory  
2MB  
Drive Installation  
Horizontal / Vertical  
41°F ~ 122°F (5°C ~ 45°C)  
5% ~ 80% (RH)  
Temperature  
Humidity  
Operating  
Environment  
The DVD Writer is not  
detected after it is connected  
to a sound card.  
The interface mode of the sound card is AT-BUS.  
You must therefore connect the DVD Writer to the EIDE  
port on the PC mother board, rather than to the sound card,  
or install an EIDE compatible sound card.  
Cleaning Your Discs  
(Choose the SL Jumper)  
(Choose the MA Jumper)  
MainBoard  
DVD  
Hard Drive  
Size (Width x Height x Length)  
5.83 X 1.65 X 6.69 Inch (148.2 X 42 X 170mm)  
750g  
Plate  
Writer  
Horizontal  
Bracket  
Do not touch the surface  
of a disc; hold it by the  
edges.  
To clean a disc, polish lightly  
from the inside of the disc to the  
outside with a soft cotton cloth.  
Weight  
* The product specifications above may be changed improve  
device performance without prior notice.  
The disc may not function properly if there are fingerprints, foreign substances or  
dust on the disc surface.  
5
7
8
9
6
 

Raymarine Fish Finder L265 User Guide
RCA CRT Television NCJ11 User Guide
RCA Telephone 29257 User Guide
RedMax Edger HEZ2601F User Guide
Rheem Water Heater AP15317 User Guide
Ricoh Printer AP505 User Guide
Saitek Video Game Controller R660 User Guide
Samsung MP3 Player DVD V1000 User Guide
Scotts Lawn Mower S2546 User Guide
Sears Patio Furniture D71 M25961 User Guide